Presently for you to permit (empower) a Cisco switch to start steering IPv6 bundles, you'll have to play out the accompanying two errands.
Empower IPv6 directing universally on the switch; and afterward empower IPv6 handling on a specific interface(s).
To start following through with responsibility number one (empowering IPv6 steering internationally on a switch) you'll have to enter Worldwide Setup mode and type ipv6 unicast-directing on the switch like you see here:
Router>enable
Router#configure terminal
Router(config)#ipv6 unicast-steering
Router(config)#exit
Router#
Notice, that I composed "empower" while the switch was in Client Executive mode (Router>) which then, at that point, put the switch into Advantaged Executive mode (Router#). Then, at that point, when the switch was in Favored Executive mode (Router#) I composed the words "design terminal" which then, at that point, put the switch into Worldwide Setup mode (Router(config)#) so I could start arranging the switch to universally course IPv6 bundles; and as may be obvious, I composed the Worldwide Arrangement order "ipv6 unicast-steering" to finish responsibility number one.
In this way, to spare the nitty-gritty details, the order that you want to type on a Cisco switch to empower it universally for IPv6 bundle steering is "ipv6 unicast-directing".
Presently, that I've effectively gotten done with job number one, I composed "exit" to leave Worldwide Setup mode (Router(config)#) and reemerged into Advantaged Executive mode (Router#).
Router>enable
Router#configure terminal
Router(config)#ipv6 unicast-directing
Router(config)#exit
Router#configure terminal
Router(config)#interface fastethernet 0/0
Router(config-if)#ipv6 empower
Router(config-if)#
- https://christinanoto.sites.gettysburg.edu/education/benham/receiving-c1000-010-pdf-dumps-is-crucial-things-for-exam-preparation
- https://christinanoto.sites.gettysburg.edu/education/benham/c1000-088-pdf-dumps-assists-you-to-improve-preparation-expertise
- https://christinanoto.sites.gettysburg.edu/education/benham/c1000-067-pdf-dumps-to-improve-your-chances-of-results
- https://christinanoto.sites.gettysburg.edu/education/benham/c1000-003-pdf-dumps-to-boost-your-chances-of-accomplishment
- https://christinanoto.sites.gettysburg.edu/education/madeleine-1/c2090-011-pdf-dumps-to-improve-your-chances-of-accomplishment
- https://christinanoto.sites.gettysburg.edu/education/madeleine-1/c2090-424-pdf-dumps-exam-preparation-approaches-for-improved-learning
- https://christinanoto.sites.gettysburg.edu/education/benham/getting-c1000-056-pdf-dumps-is-essential-items-for-exam-preparation
- https://christinanoto.sites.gettysburg.edu/education/madeleine-1/arranging-to-take-c2090-930-exam-attempt-c2090-930-pdf-dumps-for-prep
- https://christinanoto.sites.gettysburg.edu/education/madeleine-1/c9560-503-pdf-dumps-assists-you-to-enhance-preparation-abilities
- https://christinanoto.sites.gettysburg.edu/education/madeleine-1/c9560-507-pdf-dumps-helps-you-to-improve-preparation-expertise
Presently, since the switch is once more into Favored Executive mode (Router#), I progressed forward to finishing job number two (empowering IPv6 handling on a specific interface(s). By re-composing the order "design terminal" which set the switch once more into Worldwide Arrangement mode (Router(config)#), so I could utilize the "interface" order to determine the connection point type (fastethernet) and its opening and port data (0/0). Notice, that the switch has gone into Connection point Setup mode (Router(config-if)#) by stirring things up around town key, and when the switch was in Point of interaction Arrangement mode (Router(config-if)#); I utilized the point of interaction order "ipv6 empower" to empower the fastethernet 0/0 connection point for IPv6 handling to get done with responsibility number 2.
Here is another way the past orders might have been composed:
Router>enable
Router#configure terminal
Router(config)#ipv6 unicast-steering
Router(config)#interface fastethernet 0/0
Router(config-if)#ipv6 empower
Router(config-if)#exit
Router#
Notice, that it wasn't exactly important to leave Worldwide Setup mode (Router(config)#) to follow through with the two jobs; I just made it happen, to show you each undertaking separately.
I welcome you to visit my site were you'll find the most recent data with respect to Cisco IPv6 Plan and Execution Strategies.
To your prosperity,
Charles Ross, CCNP #CSCO10444244 is the proprietor of Ittechtips.com; where you'll find free thorough data and recordings about IPv6 innovation and how it functions with Cisco Frameworks techonoloy.