Presently, some of you perhaps pondering, for what reason did he compose an article on the most proficient method to empower EIGRPv6 on a Cisco Switch, when I definitely know how to do that?
Indeed, to cut to the chase, empowering EIGRP on a switch that is running on an IPv6 organization, is somewhat not the same as empowering EIGRP on a switch that is running on an IPv4 organization.
Meaning, a switch that is running on an IPv6 organization, had EIGRP (EIGRPv6) empowered per interface, rather than internationally like a switch running on an IPv4 organization would. In this way, at the end of the day, while empowering EIGRPv6 on a Cisco switch, you don't have to utilize the "network" order when the switch is in Switch Design Mode.
Rather you'll have to play out the accompanying advances:
1. Router>enable
2. Router#configure terminal
3. Router(config)#ipv6 unicast-directing
4. Router(config)#interface type number
5. Router(config-if)#ipv6 empower
6. Router(config-if)#ipv6 eigrp as-number
7. Router(config-if)#no closure
8. Router(config-if)#ipv6 switch eigrp as-number
9. Router(config-router)#router-id {ip-address | ipv6-address}
10. Router(config-router)#no closure
11. Router(config-router)#exit
12. Router(config)#exit
13. Router#copy run start
Steps Made sense of:
Step #1
1. Router>enable
Places switch into Favored Executive mode.
Step #2
2. Router#configure terminal
Places switch into Worldwide arrangement mode.
Step #3
3. Router(config)#ipv6 unicast-directing
Arranges the switch to course IPv6 parcels
Step #4
4. Router(config)#interface fastethernet 0/0
Determines the fastethernet 0/0 connection point on which EIGRPv6 is to be arranged.
Step #5
5. Router(config-if)#ipv6 empower
Empowers IPv6 handling on the fastethernet 0/0 connection point.
Step #6
6. Router(config-if)#ipv6 eigrp 1
Empowers the EIGRP for IPv6 process on the fastethernet 0/0 connection point.
Step #7
7. Router(config-if)#no closure
Begins the EIGRP for IPv6 convention (process) without changing any per-interface arrangement.
Step #8
8. Router(config-if)#ipv6 switch eigrp 1
Places the switch into switch setup mode and makes an EIGRP for IPv6 directing cycle.
Step #9
9. Router(config-router)#router-id {ip-address | ipv6-address}
Empowers the switch to utilize a decent switch ID. (Recall every switch Id should be one of a kind)
Step #10
10. Router(config-router)#no closure
Put the EIGRPv6 directing cycle in "no closure" mode to begin the EIGRPv6 cycle.
Step #11
11. Router(config-router)#exit
Returns the switch to Worldwide setup mode
- https://jovian.ai/amanibarker/get-des-4122-dumps-pdf-to-enhance-your-preparation-skills
- https://jovian.ai/terryjarrett193-3/acquire-ms-220-dumps-pdf-to-have-success-in-1st-attempt
- https://jovian.ai/terryjarrett193-3/ms-720-dumps-pdf-the-essential-element-for-preparation
- https://jovian.ai/terryjarrett193-3/ms-203-dumps-pdf-will-lower-your-exam-tension
- https://jovian.ai/terryjarrett193-3/get-ms-600-dumps-pdf-to-boost-your-preparation-abilities
- https://jovian.ai/terryjarrett193-3/get-ms-700-dumps-pdf-to-acquire-good-results-in-first-try
- https://jovian.ai/terryjarrett193-3/ms-900-dumps-pdf-the-essential-element-for-preparation
- https://jovian.ai/terryjarrett193-3/ms-101-dumps-pdf-will-decrease-your-exam-stress
- https://jovian.ai/terryjarrett193-3/get-ms-500-dumps-pdf-to-enhance-your-preparation-expertise
- https://jovian.ai/terryjarrett193-3/get-ms-100-dumps-pdf-to-get-results-in-1st-try
Step #12
12. Router(config)#exit
Returns the switch to Special Executive mode.
Step #13
13. Router#copy run start
Saves the items in the running-config to nearby Non - Unpredictable Irregular Access Memory (NVRAM).
I welcome you to visit my site were you'll find the most recent data with respect to Cisco IPv6 Plan and Execution Methods.
To your prosperity,
Charles Ross, CCNP #CSCO10444244 is the proprietor of Ittechtips.com; where you'll find free complete data and recordings about IPv6 innovation and how it functions with Cisco Frameworks innovation.